Results 1 to 5 of 5

Thread: Drift Boat

  1. #1
    Join Date
    Feb 2007
    Posts
    5

    Default Drift Boat

    Just received some plans for a drift boat I ordered. It is a MacKinzee (sp?) style boat built with epoxy and plywood and reinforced with fiberglass, about 11 foot with a motor well in the center. Have been excited about building it, BUT finding the right kind of plywood is proving to be difficult. There just dosen't seem to be anywhere around here (within 200 miles or so) to obtain said ply (okoume BS108. Any ideas?

  2. #2
    Join Date
    Jan 2006
    Posts
    889

    Default

    AWITE, first things first, McKenzie, being the proud owner of it(you), that's how it's spelled
    Most kits call for a 1/4-3/8" Marine grade plywood, some of your high end cabinet shops can get it, as well as large dstributors of specialty woods.
    Heck any lumber distributor ought to be able to get it for ya, even if they don't stock it.
    A friend of mine built a similar 15' boat, minus the motor thing, it's light & has held up very well. The one thing he didn't do was make the front & rear casting floors level, there is a slight grade there that is very uncomfortable over the course of a days fishing. He's planning on building a 16' later on with level casting floors front/rear, he really enjoyed building the first boat, it's low maintainance other than the wood gunnels & casting braces that require a little refinishing every few years.
    Good luck with the boat.

    Grumpy

  3. #3
    Join Date
    Feb 2007
    Location
    Southeast Tennessee
    Posts
    18

    Default

    I built one several years ago & probably will build a Montana Boat Builders kit later this year. Cleveland Plywood in Cleveland TN can order it for you! Ask for Tammy Rogers & ask bout ordering it. I did find it cheaper at some wood place in St Louis but w/ freight these days would drive the cost through the roof. If you are going to use it in tailraces such as Hiwassee I would urge you to consider magohaney marine grade instead of fir... will take blows much better!!!

  4. #4
    Join Date
    Feb 2007
    Location
    Southeast Tennessee
    Posts
    18

    Default

    BTW Cleveland Plywoods # is 423-472-3357

  5. #5
    Join Date
    Feb 2007
    Posts
    5

    Default Drift Boat Help

    I appreciate the lead on Cleveland Ply. I wanted to try to find a place I could drive to in an hour or two. Thanks for the other help also. From what I have read, the Okoume is also a hardwood and is also light. They say fir must be coated in fiberglass and tends to shirnk in the process. The BS1088 is a Ply spec from the UK

Similar Threads

  1. i built a drift boat
    By 2weightfavorite in forum Boats, Canoes and Kayaks
    Replies: 4
    Last Post: 09-06-2015, 10:36 AM
  2. Drift Boat for Sale
    By David Knapp in forum Boats, Canoes and Kayaks
    Replies: 1
    Last Post: 09-10-2014, 02:42 PM
  3. drift boat anchor
    By billyspey in forum Boats, Canoes and Kayaks
    Replies: 0
    Last Post: 07-22-2010, 09:32 PM
  4. Drift Boat
    By Steve Wright in forum Tennessee Trout Streams and Tailwaters
    Replies: 1
    Last Post: 06-10-2010, 05:26 AM
  5. Where can I use my drift boat?
    By easttnsalmon in forum Smoky Mountain Fishing
    Replies: 5
    Last Post: 06-23-2009, 06:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •