Home Register Today's Posts Members User CP Calendar FAQ

Go Back   Little River Outfitters Forum > Fly Fishing Board > Boats, Canoes and Kayaks

Thread Tools Display Modes
Old 03-16-2012, 03:18 PM
Rodonthefly Rodonthefly is offline
Senior Member
Join Date: Jul 2009
Posts: 407
Default to anchor or not

Ok this topic may have already been talked about here, but I was wondering. Ok anyone knows me knows that I float and fish the Clinch most of the time. With all the high water we are haveing, who drops anchor? and trys to fish high water on the Clinch?

I personaly have tried it, hung and lost two anchors. Not to mention almost sank the boat one time and the other I about threw some one out of the boat. IMO I think it can be done with one but on two it's just been to much **** trouble for me.
Reply With Quote
Old 03-16-2012, 06:11 PM
Corbo Corbo is offline
Senior Member
Join Date: Apr 2010
Location: Sevierville TN
Posts: 494

Now we know how Shawn accumulated so many anchors!

Just a thought/suggestion... consider tying a float onto your anchor line near where it is attached to your boat so you can retrieve at low water. In an emergency you can cut the line and the float is already on your line.

My friend Bill got pulled out of his boat on the Delaware River many years ago... he was stuck on bottom and had a lot of line in his boat when the boat went side-ways in the current... he could not hang on any longer so he let go of the line and was promply hauled overboard as the line was wrapped around his leg. he was lucky to survive.

Be careful so your boat doesn't wind up in a "widow's sale".
Reply With Quote
Old 03-16-2012, 07:44 PM
old east tn boy's Avatar
old east tn boy old east tn boy is offline
Senior Member
Join Date: Feb 2010
Location: Farragut, TN is home
Posts: 116
Default no anchor

I lost one anchor on the Clinch after deciding that was better than capsizing. Two generators were running. I'll never do that again!
Reply With Quote
Old 03-16-2012, 11:01 PM
waterwolf waterwolf is offline
Senior Member
Join Date: Jun 2008
Posts: 1,316

I have only lost one anchor in the clinch and it was during a spilling episode, right above the jail. I dropped anchor to help net a fish, and the current wouldn't allow it to catch until it wedged in cut in one of the ledges. It **** near yanked us out of the boat. The solution was easy in a drift boat, I simply released the anchor catch and let all the rope feed out. Went back a week later and got everything back.

I would not recommend anchoring on spilling water levels or sluicing water levels. However, I have never had issues with 2 generator flows, and do it routinely when I am out on those flows.

If you are smart about it, and know the warning signs of a dangerous situation it is very easy to either cut the rope or let it slip through to avoid getting dumped.
Reply With Quote
Old 03-17-2012, 11:06 AM
MadisonBoats's Avatar
MadisonBoats MadisonBoats is offline
Senior Member
Join Date: Nov 2008
Location: Norris, TN
Posts: 2,093

Oh man! I sure do find tons of anchors on the river. Oddly enough; most of them are not wedged or hung up. Most of them are found in open areas with not obstructions.

I would never anchor with the river spilling. I think you could really get yourself hurt or sink your boat. I know of several flipped boat accidents already this past Winter.

I think the mushroom anchors work the best on one-two generators. Note; not in holding position but, in just slowing your drift hand letting them drag.

The forked anchors (river anchors) will always find a nice shoal to get hung on and they are easily lost.

I personally like using my chain-ball on the river in most conditions. However; I have lost one due to a pulley failure.

There is a simple technique to help retrieve stuck anchors. It involves wrapping a piece of rope around the base(bottom) of the anchor so that it can be leverage from the bottom up to reverse pull it from its stuck position. Run the tag end of the rope up the side of the anchor and feed a folded strand of the rope through the anchor top. Use some electrical tape and tape the rope around the anchor side. Make a folded knot on the initial side of the anchor mount to attach the main anchor rope.

The idea is that if you get hung; you can pull up hard and tear the tape. The rope will pull out of the anchor hole and pull tight to the bottom mounting position and allow you to retrieve the anchor from the bottom.

Also; another tip is to make an arrester in one end of the rope to act as a shock absorber in fast current. This simply involves folding your anchor rope and wrapping twine or tape around it to hold in normal use. In case of a hang; it will tear the binding and release the extra line to cushion the snag.

Here is a picture of one I made for a friend.

*Also; if you lose your anchor and need a new one-send me an email and I should be able to hook you up with a one I have found. Free of course!

**Here is a link to an excellent website about river anchoring. He also has tons of great fishing and boating information. http://www.sschapterpsa.com/ramblings/Anchoring.htm
“Every human has four endowments- self awareness, conscience, independent will, & creative imagination.
These give us the ultimate human freedom... The
to choose, to respond, to change.”

Last edited by MadisonBoats; 03-17-2012 at 11:39 AM..
Reply With Quote
Old 03-18-2012, 08:49 PM
Rodonthefly Rodonthefly is offline
Senior Member
Join Date: Jul 2009
Posts: 407

So what kind of anchors do you guys use? Also do you pick your spots to drop or could you care less about ledges logs etc? Seems everytime I have droped anchor I don't stop untill I catch a ledge and its to late.
I have been to dag gum tight to but a drift boat anchor, and have always used a mushroom anchor that's 25 or 30 pounds. Is that my problem?
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -4. The time now is 10:15 PM.

Powered by vBulletin®
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.